Top Gun DR650 License Plate
Bracket
Bracket
 |  |  |  |  |  |
Copyright © 2006 Top Gun Motorcycles. All rights reserved. Distribution or publication of this document (electronic or otherwise)
is prohibited without the express written consent of the author. For more information or to request permission to publish this
document, please see our contact page. For information on our pledge to maintain your privacy click here. To learn more about
your friends at Top Gun Motorcycles, read about us here.
is prohibited without the express written consent of the author. For more information or to request permission to publish this
document, please see our contact page. For information on our pledge to maintain your privacy click here. To learn more about
your friends at Top Gun Motorcycles, read about us here.
| Top Gun Motorcycles |
| DR-650 License Plate Bracket |
| Bracket installed. Note the light is barely visible beneath the fender. |
| Here's what you're replacing! |
DR650SE License Plate Bracket ('96 - Present)
Although the DR650 doesn't seem to eat license plates quite like the KLR650, the rear
fender assembly is still big, heavy, and ugly. We've designed this bracket to fit into the
existing fender holes, and replace the entire assembly with one neat, aluminum bracket.
The bracket is made from .125” 5052 aluminum, providing more than enough strength
for the bracket without being too brittle to resist vibration and shock. The bracket is
CAD designed and laser cut to ensure a precise fit on your DR650.
Installing this bracket removes the stock reflector and tail light from your DR650. The
bracket features a pre-cut, 8mm hole for installation of an optional license plate light.
Please check your local ordinances to ensure compliance.
The license plate bracket is available exclusively through Multisurface Motorcycle
Products. They also stock an aluminum-housed LED light, specifically chosen to fit
underneath the fender.
Although the DR650 doesn't seem to eat license plates quite like the KLR650, the rear
fender assembly is still big, heavy, and ugly. We've designed this bracket to fit into the
existing fender holes, and replace the entire assembly with one neat, aluminum bracket.
The bracket is made from .125” 5052 aluminum, providing more than enough strength
for the bracket without being too brittle to resist vibration and shock. The bracket is
CAD designed and laser cut to ensure a precise fit on your DR650.
Installing this bracket removes the stock reflector and tail light from your DR650. The
bracket features a pre-cut, 8mm hole for installation of an optional license plate light.
Please check your local ordinances to ensure compliance.
The license plate bracket is available exclusively through Multisurface Motorcycle
Products. They also stock an aluminum-housed LED light, specifically chosen to fit
underneath the fender.
- Computer designed, laser cut for precise fit
- .125" 5052 Aluminum specifically provides strength without being brittle
- Uses stock fasteners and existing bracket holes for easy installation
- Pre-cut for installation of optional license plate light
 |
 |
 |
 |
 |
 |
 |
Get your bracket
Today at:
MMP Products
For your DR and
KLR needs!
Bracket
Installation
Instructions
Today at:
MMP Products
For your DR and
KLR needs!
Bracket
Installation
Instructions
| A good view of MMP's optional license light tucked under the fender. |
For those of you who would like a license light on your bracket, installation requires a
few extra steps and your choice of electrical connectors and tools. We recommend you
follow the basic steps below (after removing the stock bracket - see installation
instructions):
Now go ride with your new tail light and bracket!
few extra steps and your choice of electrical connectors and tools. We recommend you
follow the basic steps below (after removing the stock bracket - see installation
instructions):
- Install tail light on Top Gun bracket. NOTE - Be careful not to over-tighten the
light to avoid damage to threads or light casing. Adjust the light to be as far
above the tail bracket as possible without hitting the fender. This will allow the
light to shine on the plate even with a license frame installed, and should also
keep the light source from being visible (a traffic infraction in most areas - "white
light to the rear.") - Cut the stock wiring as close to the stock tail light as possible leaving only
enough wire on the stock light to allow reconnection in the future (if desired). - We recommend using heat shrink to seal your connections, especially if
soldered, though it may not be required with other connector types. Remember
to slide heat shrink onto the wire BEFORE making the connection! - Continue installation of the bracket and carefully route the wire harness along
the frame back to the stock connector.
Now go ride with your new tail light and bracket!
| This is the tail light connector on the right side of the bike under the seat. |
For all product ordering/information, contact MMP at sales@multisurfacemotorcycling.com Multisurface Motorcycle Products |